Leading 10 usual forklift accidents ， forklift operation should pay attention to these matters ！.

Don't take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious mishaps in mins, and there are several crashes entailing forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside shelf, which almost causes an crash.
Instance 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not discover the forklift.
Case 6: The forklift raises the employees illegally, the forklift chauffeur does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation should pay attention to these issues ：.

Begin.
1. Prior to starting, observe the surroundings, and after validating that there are no challenges that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be slanted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the lots is traveling, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork ought to be decreased to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will create the lorry to lose lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and must keep a certain security distance from the car in front. .
7. When the forklift is running, the tons has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be properly slanted back. The lots will not be elevated other than when piling or packing. .
8. The height of the load must not block the driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when reversing.
9. It is restricted to activate the ramp, neither to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a low speed when entering the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to depend on the fork to hold things and play a balancing role. .
12. If troubles are located, they will be repaired and reported in a prompt way, and they will never ever run with diseases or conceal them.

filling and discharging.
1. When fork-loading items, the range between the two forks need to be changed as needed to make the lots of the two forks well balanced and not skewed, and one side of the item need to be against the shelf. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise bordering pedestrians. .
3. In the process of packing and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the tons, and it ought to be kept in mind that the fork tip must not touch various other products or things. The load ought to be maintained with minimal back tilt of the gantry to ensure that the load does not slide in reverse. The pole can be tilted ahead a little when the load is reduced to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, put, round or roll objects. .
10. It is not allowed to utilize forks to choose, turn pallet discharge.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the vehicle driver does not leave the lorry's line of vision and does not exceed 1 minute).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be examined, and gas, lubing oil and cooling water ought to be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. During the operation of the forklift, check whether the stress and temperature level are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You should check prior to leaving the auto;.
2. When you come across somebody before you during driving, you need to send Stand-on Electric Pallet Stacker a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming should not be too sharp to avoid the propensity of Stand-on Electric Pallet Stacker " complimentary switching";.
6. Adding and down the slope needs to be sluggish and uniform, and no activating the incline is permitted.
7. Do not drive throughout the slope. When the gradient is higher than 10%, the car needs to be driven in reverse when worsening;.
8. When the forklift workers lug the goods and progress, if they run into huge or heavy products and go to the chauffeur's view, they ought to take the turning around workout
.
The "Eight Prohibitions" need to be adhered to in the procedure.
1. Single fork operation is not enabled.
2. It is not allowed to raise the goods for far away driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not allowed to use braking force to expatriation round or easy-to-roll things.
7. It is not enabled to bring people to work with the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is elevated.
8. Do not drive laterally on inclines
.
Auto parking is not permitted under the list below problems.
1. Curves, narrow roads, railway crossings;.
2. Areas with a longitudinal slope more than 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the area with the very same length as the challenge ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844